Today Geohot released his blacksn0w software unlock for the iPhone 3G and the iPhone 3GS. If you would like to unlock your iPhone on firmware 3.1.2 and use them with other carriers, this tutorial will show you how.
Today Geohot released his blacksn0w software unlock for the iPhone 3G and the iPhone 3GS. If you would like to unlock your iPhone on firmware 3.1.2 and use them with other carriers, this tutorial will show you how.
blacksn0w is a software unlock developed by Geohot for both iPhone 3G and iPhone 3GS users. It works with the latest baseband 05.11.07 and is scheduled to be released on November 4.
Two weeks ago, Geohot released his blackra1n iPhone 3.1.2 jailbreak. The blackra1n jailbreak software worked with all iPhones and iPod touches running on iPhone 3.1.2 firmware except for the newer 8GB iPod touch (MC models) that Apple released after the September 9 event. The blackra1n jailbreak also did not work on the newer iPhone 3GS which Apple patched the 24kpwn exploit in. blackra1n RC2 works with all iPhone and iPod touches, but the newer iPod touch and iPhone are only tethered jailbreaks. Tethered means that you will need to run blackra1n each time you reboot your iPhone or iPod touch. If you were an iPhone 3G user, you most likely had to try many different methods to get blackra1n to work. Geohot has fixed the iPhone 3G problem so blackra1n should now jailbreak without any problem.
If you already did jailbreak your iPhone or iPod touch, you don’t need to use blackra1n again.
Here is how you can jailbreak iPhone 3.1.2 firmware using blackra1n RC2.
1. Download blackra1n RC2 (Available for both Windows & Mac)
2. Follow the steps at my jailbreak iPhone 3.1.2 post.
I tried blackra1n on Windows 7, but it crashed when I first tried opening it. To get blackra1n to work on Windows 7, do the following:
1. Right-click the blackra1n icon and click properties.
2. Click the Compatibility tab.
3. Under compatibility mode click the box to enable it and select Windows XP (Service Pack 2). Click OK, and then run blackra1n.
I’ve only tried this on a Windows 7 32-bit setup, but it should work on a 64-bit setup as well.
The iPhone 3.1.2 update that Apple released last week required users of jailbroken iPhones or iPod Touches to wait for a new jailbreak software to be released before updating. There was no jailbreak available until Geohot released his new blackra1n 1 click jailbreak software. The blackra1n software is available for both Windows and Mac users, but it only supports iPhone, iPhone 3G, iPhone 3GS, and iPod Touch. blackra1n does not support the iPod Touch 3rd generation 8 GB models that have a MC in the model number. Many iPhone 3G users reported having a problem with blackra1n on iPhone 3G, if you were one of them please leave a comment telling us what problems you encountered and how you solved them. I will be making a blackra1n troubleshooting guide to help users that have any problem with it. You can jailbreak iPhone 3.1.2 with blackra1n, but you cannot unlock iPhone 3.1.2. To unlock iPhone 3.1.2, you must use PwnageTool 3.1.4 which the Dev-Team recently released.
If you want to just jailbreak iPhone 3.1.2 I recommend you use blackra1n, but if you want to unlock then you have no choice but to use PwnageTool which only works with Mac. If you haven’t already downloaded iPhone 3.1.2 or updated, the download links for it are below.
Note: Do no’t use Safari to download iPhone 3.1.2 IPSW files, instead use another browser. Safari downloads this as a .ZIP and iTunes is not able to recognize the firmware that way.
2. Click the make it ra1n button.
3. Your iPhone or iPod Touch will reboot once blackra1n is done doing it’s thing and you should see the blackra1n icon on there. If you don’t see the blackra1n icon, go to the last page on your iDevice and you should see it.
4. Install your preferred aplication from the blackra1n app. You have the option of choosing Cydia, Icy, or Rock. I don’t recommend you to install them all at once, because that may cause problems. Install them one at a time.
1. Download PwnageTool 3.1.4 (only works with Mac!)
2. You will be creating a custom IPSW and then restoring it through iTunes. If you don’t know how to do that, read my jailbreak iPhone 3.1 with PwnageTool post which gives step by step instructions.
Update #2: Want to unlock iPhone 3.1.2? Go to my download and install blacksn0w post to unlock.
Update #1: Go to my jailbreak iPhone 3.1.2 with blackra1n post to jailbreak your iPhone or iPod Touch!
Today the iPhone 3.1.2 update was released to iPhone, iPhone 3G, iPhone 3GS, and iPod Touch usres. This update includes mainly bug fixes. If you would like to jailbreak or unlock your device, you must read this. If you have an unlocked iPhone 3G or iPhone 3GS do not update to this new firmware, updating to the iPhone 3.1.2 firmware will permanently update your baseband. The newer baseband does not support software unlocking.
The jailbreak has not been released yet, but you if you’ve got too much time on your hands you may be able to jailbreak if you try the following. If this works please share your results in the comments.
1. Update to iPhone 3.1.2. After updating, find your iPhone 3.1.2 IPSW file or download it using any of the links below. Remember, don’t use Safari to download. Safari can’t download .IPSW files properly, use a different browser!
2. Download redsn0w.
3. Follow the jailbreaking guide at the Jailbreak iPhone 3.1 post.
It’s possible to unlock iPhone 3.1.2 but only if your baseband has not been updated to 05.11.07 or the newer baseband, you must create a custom firmware that uses the 04.26.08 baseband. The iPhone 3.1.2 update updates the baseband to a newer one that permanently blocks the software unlock. A guide on how to unlock iPhone 3.1.2 will be up once a jailbreak tool is released.
For now, follow @QuickPWN and subscribe to QuickPwn YouTube channel for updates.
Any linkbacks on your blog are appreciated. We are also creating
guides for users on how to download Cydia’s On File so they can be
safe from future updates.
Apple released their iPhone 3.1 firmware on September 9, and now the iPhone Dev Team has released their Pwnage Tool 3.1 software which can jailbreak iPhone 3.1. There is no Windows Pwnage Tool 3.1, it only works for Mac. If you’re a Windows user then you’ll have to wait for the iPhone Dev Team to release redsn0w. If you’re a Mac user, then follow the steps below to jailbreak iPhone OS 3.1.
The Pwnage Tool 3.1 software only works on the following devices: iPod Touch 3.1.1 (first generation only), iPhone 3.1 (first generation), and iPhone 3G 3.1. As of right now the iPhone 3GS, iPod Touch 2nd generation, and the new iPod Touch 3rd generation are not supported.
1. Download Pwnage Tool 3.1 (Filename: PwnageTool_3.1.dmg Filesize: 23.1 MB).
2. Double-click the Pwnage Tool icon to launch Pwnage Tool. You may get a message that says “PwnageTool is an application downloaded from the Internet. Are you sure you want to open it?“. Just click Open.
3. When Pwnage Tool 3.1 launches you will see a message that says “Copyright 2009 iPhoneDevTeam. This software is not for commercial use. If you bought this software demand a refund. It is not for sale. We are not responsible for any damage this software may do to any of your equipment, BE WARNED.” Just read it and click Ok.
4. Click on the device you want to jailbreak. I have an iPod Touch so I’ll click the iPod Touch in Pwnage Tool. After selecting the device click the arrow in the bottom right corner.
5. Pwnage Tool will now attempt to locate the IPSW file for your device. If you don’t have it downloaded already, here are the download links (iPod Touch download links will not be added here because they expire):
6. Once Pwnage Tool finds your IPSW click on it. If it doesn’t find it then you can manually browse and locate it. Click the blue arrow in the bottom right corner of the Pwnage Tool application to continue.
7. Pwnage Tool will now show a message saying something like “We will now create an ipsw file that you can use to restore your iPod Touch (2G) with iTunes. This file will be placed on your desktop. Do you want to continue?“. Click Yes.
8. Pwnage Tool will now start building the IPSW. You will be prompted to enter in your password, just enter in your password and click Ok.
9. Once your IPSW has been buit, Pwnage Tool will display the following message: “Has your iPod Touch (2G) been Pwned before (does it have the pineapple logo)? If you are unsure click No.“. Just go ahead and click No.
10. Time to put your device in DFU mode. Pwnage Tool will guide you through the steps.
11. Once you have successfully put your device in DFU mode Pwnage Tool will display the following: “Successfully entered DFU mode! Close the Pwnage Tool application, start iTunes and restore with your custom firmware bundle.” Just click Ok.
12. Now open iTunes (make sure you have iTunes 9!). If you don’t have iTunes 9 then download it and install it now.
13. Once you launch iTunes 9, press option on your keyboard and click Restore in iTunes. Find the IPSW file that is named something like iPod1,1_3.1.1_7C145_Custom_Restore.ipsw. Make sure it has Custom in the name of the file and then click Choose.
14. iTunes will now restore the custom IPSW file to your iPhone or iPod Touch. Once it’s done you’ll see Cydia and Icy on your device! Congratulations, you are done jailbreaking iPhone 3.1 firmware.
You can jailbreak iPhone 3GS 3.1 and iPod Touch 3rd generation, but the jailbreak is not out for it yet. I’ll create a guide on how to jailbreak it once the software for it is released. Stay tuned!
Update: This tutorial does not install Cydia, in other words you must wait for iPhone Dev Team to release the new redsn0w software. When I saw the successfully jailbroken message on the screen I thought Cydia was installed and in all the excitement I decided to post this up for everyone else. Please wait until the new redsn0w is out. Bookmark this site and I’ll make a tutorial once it’s officially released.
With the iPhone 3.1 update which was recently released, jailbreakers will need to jailbreak their devices again. This update fixes a lot of bugs that were present in the iPhone OS 3.0 firmware, has anti-phising built-in and other cool features. In this post I will explain how to jailbreak iPhone 3.1 using redsn0w.
Note: This tutorial will be using redsn0w version 0.8. There is no redsn0w 3.1 out yet, but this worked for me on 1st Generation iPod Touch 3.1. It may not work for iPhone. If this does not work then don’t complain! I recommend you wait for the Dev Team to release the next version of redsn0w (which may be some time this week). I’ll make another tutorial once they do.
If you unlocked your iPhone and you want to keep your unlock, then don’t update to iPhone 3.1 otherwise you won’t ever be able to software unlock again (iPhone 3.1 updates the baseband permanently).
You must update to iPhone 3.1 first (if you have an unlocked iPhone you must not update yet as this will permanently lock your iPhone). After updating, either locate your iPhone 3.1 IPSW file or download it using any of the links below. Do not use Safari, instead use Firefox or Internet Explorer to download otherwise this will download as a Zip file!
3. Follow the jailbreaking guide below.
Note:
First you must download redsn0w for Windows, Mac, or Linux from here.
redsn0w 0.8 might work for Phone 3.0.1, iPhone 3G 3.0.1, iPhone 3GS 3.0.1, iPod Touch 3.0, and iPod Touch 2G 3.0.
1. Download the iPhone OS 3.0 IPSW file for your device and save it to your desktop. Here are the file names for each device, make sure you have the right one:
2. Open the redsn0w 0.8 application to jailbreak iPhone 3.0.1.
3. Click the Browse button.
4. Locate your device’s IPSW file that you downloaded in step 1 and click Open.
5. The redsn0w window will have the “IPSW successfully identified” message. Click the Next button to continue.
Today the iPhone 3.1 update was released to the public. This update fixes a lot of bugs that were present in the iPhone OS 3.0 firmware. If you want to jailbreak or unlock your device, follow the steps below. If you have an unlocked iPhone 3G or iPhone 3GS do not update just yet, updating will permanently lock your device and the ultrasn0w unlocking software won’t work.
The jailbreak has not been released yet, but you can do the following to prepare for it.
1. You must update to iPhone 3.1 first. After updating, either locate your iPhone 3.1 IPSW file or download it using any of the links below. Remember, don’t use Safari to download. Safari can’t download .IPSW files properly, use a different browser!
2. Download redsn0w (not up yet, stay tuned!).
3. Follow the jailbreaking guide at the Jailbreak iPhone 3.1 post (not up yet).
To software unlock iPhone 3.1, you must create a custom firmware that uses the current baseband. The iPhone 3.1 update updates the baseband to a newer one that permanently blocks the software unlock. A guide on how to unlock iPhone 3.1 this will be up later.
The iPhone 3.0.1 update was recently released. If you want to jailbreak any iPhone running on iPhone OS 3.0.1, you must use redsn0w 0.8. This post will show a step-by-step tutorial on how to jailbreak iPhone 3.0.1 with redsn0w.
Note:
First you must download redsn0w for Windows, Mac, or Linux from here.
redsn0w 0.8 works for Phone 3.0.1, iPhone 3G 3.0.1, iPhone 3GS 3.0.1, iPod Touch 3.0, and iPod Touch 2G 3.0.
1. Download the iPhone OS 3.0 IPSW file for your device and save it to your desktop. Here are the file names for each device, make sure you have the right one:
2. Open the redsn0w 0.8 application to jailbreak iPhone 3.0.1.
3. Click the Browse button.
4. Locate your device’s IPSW file that you downloaded in step 1 and click Open.
5. The redsn0w window will have the “IPSW successfully identified” message. Click the Next button to continue.
6. redsn0w will ask you to “Please select which options you would like to have“. Make sure the Install Cydia box has a check mark and then click Next.
7. redsn0w will ask you to make sure your device is both OFF and PLUGGED IN to your computer. Make sure you plug in your device in to your computer and then turn it off. Click Next once you have done this.
8. redsn0w will now ask you to connect your device in DFU mode, you must do this properly to jailbreak iPhone 3.0.1.
9. Once your device has successfully entered DFU Mode, redsn0w will show the following message: “Please wait while your device is being jailbroken. Waiting for reboot.” Your device should reboot after this. If redsn0w is stuck on Waiting to Reboot, unplug your USB cable quickly and plug it back in. The jailbreaking process should continue after tha.
10. Once your device has rebooted redsn0w will start uploading the RAMDisk and kernel.
11. After everything has been successfully uploaded to your device, redsn0w will have; the “Done!” message. Your device will now reboot and you should see the Cydia app on your SpringBoard. Your iPhone is now jailbroken!
See the iPhone 3.0.1 jailbreak and unlock post to unlock your iPhone 3.0.1.
Apple recently released the iPhone 3.0.1 update for iPhone users. This update was released to fix a SMS vulnerability that Charlie Miller and Collin Mulliner discovered in iPhone OS 3.0. If you have a jailbreak or unlock,
you will need to follow the below steps to keep it.
1. After updating to iPhone 3.0.1 download and install iPhone 3.0 firmware.
Download iPhone firmware 3.0 (filename: iPhone1,1_3.0_7A341_Restore.ipsw)
Download iPhone 3G firmware 3.0 (filename: iPhone1,2_3.0_7A341_Restore.ipsw)
Download iPhone 3GS firmware 3.0 (filename: iPhone2,1_3.0_7A341_Restore.ipsw )
2. Download redsn0w.
3. Follow the guide at the Jailbreak iPhone 3.0.1 post. When you select the firmware, choose the 3.0 firmware instead of the 3.0.1 firmware. This is safe and it works!
Update: If your iPhone 3GS is stuck on “Waiting for reboot” unplug your USB cable and plug it back in.
1. Follow the steps above to jailbreak your iPhone.
2. Once your iPhone is jailbroken, open Cydia.
3. Add repo666.ultrasn0w.com to your sources
4. Install ultrasn0w, and reboot!
5. Now your iPhone should be unlocked.
