Reply
Page 2 of 17:  < 1  2  3  4  12   Next > Last »
Thread Tools   Switch to Linear ModeSwitch to Hybrid ModeSwitch to Threaded Mode
Senior Member
 
Join Date: Feb 2009
Posts: 138
Posted 02-20-2009, 07:28 PM #11 (permalink)
Quote:
Originally Posted by Jmurph3 View Post
now I dont know if this would apply to both 1G and 3G iPhones but one step in the process of the 1st gen would be that after you restore and iTunes pops up with a message to insert a sim card, not to and just close iTunes and then insert the desired sim.
The pwn it.
thats how it worked for me and if i knew not to let iTunes know what sim i was using at first it would've been done in about 2 1/2 hours less time than it originally took me.
and im sure it would help several others too.

if you do add this info, i dont feel any need of credit to the guide, but it would be appreciated.
you dont need to insert any sim card..it wont take any longer i have unlocked many 2g phones after restoring all i do is close itunes and let quickpwn do the rest all this process is done in less than 10 - 15 minutes
Reply With Quote
Junior Member
 
Join Date: Feb 2009
Posts: 2
Invalid SIM, Posted 02-21-2009, 02:37 PM #12 (permalink)
Info :
Carrier: AT&T phone (where I got it from)
3G 8 Gig iPhone
Version : 2.2

I jail-broke the phone correctly because the new apps were added (cynida and installer) : please let me know if this is wrong

Installed the newest version of Yell0wsnow through cynida

I shut the phone off and inserted a SIM card from Italy VodaPhone which is locked and it recognized the fact it was locked.. I put in the corresponding pin it took the PIN and I get 1 bar for a while then it quickly says "No Service" if I try what other users have said had worked for them (airplane mode on and off) then I get and Invalid SIM card warning that does not go away even after a good while (hour)

Any suggestions or did I not do something right despite the fact that it all was loaded just as it was described in all of the things on this forum?
Reply With Quote
Junior Member
 
Join Date: Feb 2009
Posts: 10
Question, Posted 02-21-2009, 02:46 PM #13 (permalink)
once done with that close cydia and put your sim card in..after puttin it in give it 20 seconds if it doesnt find service reboot then phone and you try it over again if it doesnt find service remove sim and put it in again and wait for 30 seconds more..at this point your sim should be detected

I can find nowhere that tells me to remove my sim card. Did I miss a step??
kixfan
Reply With Quote
Senior Member
 
Join Date: Feb 2009
Posts: 138
Posted 02-21-2009, 05:15 PM #14 (permalink)
it doesnt tell u to remove your simcard..if you dont find service after updating yellowsnow on 2.2 THEN you remove your sim and insert again..repeat this step and let the sim be in the phone for atleast a minute..eventually you will find service
Reply With Quote
Junior Member
 
Join Date: Feb 2009
Posts: 1
Posted 02-22-2009, 12:33 AM #15 (permalink)
I had the problem when opening QuickPwn "The application failed to initialize properly (0xc0000135). Click on OK to terminate the application."

How do I resolve this problem?

I have already updated my Iphone 2G to FW 2.2.1. Right now, it is in emergency mode. I have it connect to my iTunes.
Reply With Quote
Junior Member
 
Join Date: Feb 2009
Posts: 2
Ok something else, Posted 02-22-2009, 02:33 AM #16 (permalink)
So is it correct or incorrect for it to say Carrier (null)(null) under settings/general/about??
Reply With Quote
Junior Member
 
Join Date: Feb 2009
Posts: 1
selecting firmware file, Posted 02-22-2009, 08:08 AM #17 (permalink)
phone details: 2g iphone, unlocked running on 1.1.3 .
Did a restore from itunes (i guess it would hv updated to 2.2.1 now..sorry i dont know how to find this)
Now my phone is locked. Im trying to run quickpwn 225.2. It is asking me to select firmware file. I dont know where to select this file from. Do i need to download. If so, which version to download and from where. Any help would be greatly appreciated. Im really worried with my phone in locked state.
Thanks a ton
Cheers
satty
Reply With Quote
Junior Member
 
Join Date: Feb 2009
Posts: 1
I need help, Posted 02-22-2009, 11:00 AM #18 (permalink)
I quick pwnd my iphone, it worked.....but I will not recongnize my cell phone provider. I did all the steps I have read, but no luck...... Can someone help me out?
Reply With Quote
Junior Member
 
Join Date: Feb 2009
Posts: 14
Posted 02-23-2009, 01:31 AM #19 (permalink)
Quote:
Originally Posted by akbar786 View Post
you dont need to insert any sim card..it wont take any longer i have unlocked many 2g phones after restoring all i do is close itunes and let quickpwn do the rest all this process is done in less than 10 - 15 minutes
yes but when after you restore it on itunes thats all that you should let it do. i went through the process of letting itunes check my sim and such. i didnt know not to do that.
lol
and no, i guess you dont have to insert a sim, but i was just mentioning how i did it.
Reply With Quote
Senior Member
 
Join Date: Feb 2009
Posts: 138
Posted 02-23-2009, 10:12 AM #20 (permalink)
Quote:
Originally Posted by satmakeshistory View Post
phone details: 2g iphone, unlocked running on 1.1.3 .
Did a restore from itunes (i guess it would hv updated to 2.2.1 now..sorry i dont know how to find this)
Now my phone is locked. Im trying to run quickpwn 225.2. It is asking me to select firmware file. I dont know where to select this file from. Do i need to download. If so, which version to download and from where. Any help would be greatly appreciated. Im really worried with my phone in locked state.
Thanks a ton
Cheers
satty

go to the downloads section of this website and download the firmware 2.2.1 for iphone NOT 3g and then save it to your desktop when quickpwn asks you for your firmware direct it to the file you downloaded..also download bootloaders if you already havent you will need those to unlock your phone
Reply With Quote
Reply « Previous Thread - Jailbreaking/Unlocking the iPhone - Next Thread »
Page 2 of 17:  < 1  2  3  4  12   Next > Last »
Thread Tools Display Modes
Linear Mode Linear Mode
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2010, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.2.0
All times are GMT -5. The time now is 12:19 AM.
Copyright © 2009 by QuickPWN. All Rights Reserved.